internal pressure

Much work demonstrated that battery sealing under vaccum can reduce the battery internal pressure.

大量的试验工作证明，在真空条件下实现电池封口，是降低电池内压的一种方法。

An approximate method for calculating the elastic stresses at the squeeze at the squeeze corner sections of an identical diameter Tee branch pipe connection under internal pressure was presented.

针对石油化工行业大量采用的等径挤压三通，提出了一个计算内压载荷下的纵向平面内挤压圆角处各应力分量的近似方法。

Internal pressure with a liquid-filled projectile is of vital importance in its reliability design.

装液弹弹内压力对弹的安全可靠性极其重要.

Reliability assessment and design of thick-walled cylinder under internal pressure

内压厚壁筒结构的可靠性分析和可靠性优化设计

The validity of computer program is verified and the high efficiency of the proposed algorithm is also demonstrated by the results of a thick cylinder problem subjected to an internal pressure.

文中给出厚壁圆筒蠕变断裂数值算例，计算结果证明了该算法的高效和正确性。

Experimental Study on the Stress of Curved Pipe Under Internal Pressure

内压作用下弯管应力的实验研究

This paper deals with the function relations of principal stress and principal stain of a thin-walled cylinder varying with time, and the relations between the principal stain rate and the thickness of a thin-walled cylinder, as it is subjected to internal pressure.

给出了薄壁圆筒受内压时，主应力、主应变随时间变化的函数关系，以及主应变速率与圆筒壁厚的联系。

Cryogenic containers are equipped with pressure relief devices to control internal pressure.

低温容器要配备有减压装置,以控制内部压力.

Under the conditions of the same internal pressure, with the relative bending radius increased, ellipticity and the thickening rate of internal measuring point decreased; the thickening rate of outer measuring point gradually were also decreased.

在充液压力相同的条件下，随着相对弯曲半径的增加，椭圆度逐渐减小；内侧点的增厚率逐渐减小；外侧点的减薄率逐渐减小。

In the present paper, the shakedown problems of power hardening and elastic power hardening thick-walled cylindrical tube under a cycling internal pressure are studied.

本文讨论了幂强化材料以及弹性&幂强化材料厚壁圆筒在循环内压作用下的安定性；

The distribution of the stress in casing connection, the value of make-up torque and thread off load are studied when the casing connection is assembled or loaded with internal pressure and axial tension, which are very important for gluing, leakage and thread off failure analysis.

套管接头在装配、内压和拉伸载荷工况条件作用下，沿接头的应力分布规律、上扣扭矩和滑脱力的大小，对分析套管接头粘扣、泄漏和滑脱的失效有重要参考价值。

Internal Pressure Measurement for Thick Wall Cylinder In Impact Fatigue Test

带内裂纹厚壁圆筒管冲击疲劳实验中内压测定技术

Ring Tension Stress Analysis of Elliptic Section Bend Pipe by the Action of Internal Pressure

椭圆形截面管受内压作用的环向应力分析

Aim To study the internal pressure variation of liquid filled cylindrical shell under axial impact.

目的研究充满液体的圆柱壳轴向冲击过程中的内压变化规律.

An Engineering Analysis Approach for Squeeze Equal-diameter Tee Branch Pipe Connection Strength under Internal Pressure

等径挤压三通强度分析工程方法

Plastic limit load of viscoplastic thick-walled cylinder and spherical shell subjected to internal pressure is investigated analytically using a strain gradient plasticity theory.

基于应变梯度塑性理论，分析了内压作用下厚壁圆筒和球壳的塑性极限荷载。

Method of reducing internal pressure of Ni MH battery and increasing cycle life

MH-Ni电池降低内压延长寿命的方法

Circumferentially oriented fibers increase the internal pressure containment capability of the flow tubes.

圆周方向取向的纤维增加流量管容纳内部压力的能力。

The thermal pressure is obtained by the principle of corresponding state and the internal pressure is derived from Lennard-Jones ( 6,12) potential.

聚合物的热压力由对应状态原理得到，内压力由Lennard Jones（6,12）势能函数导得。

There are no bolts for axial stress of internal pressure and no metal gaskets.

没有受力螺栓，省去了金属垫片或垫块；

Results suggest that after injection, most internal pressure of left ventricle reduce, very few keep unchanged.

结果显示给予乙醇后, 大多数左心室内压降低, 个别左心室内压不变.

A simplified hard-body equation of state and its applications(ⅱ) prediction of thermal pressure coefficient and internal pressure of liquids

简化刚体状态方程及其应用Ⅱ.液体热压力系数和内压的预测

The Elastoplastic FEM Simulation of Free Bulge Forming of Metal Tubes under Internal Pressure and Axial Compression

金属园管在内压及轴向压力作用下自由胀形的有限元法模拟

Study on Plastic Limit Load of Extruded Piping Tee under Internal Pressure

内压下挤压三通的塑性极限载荷研究

According to the theory of stress analysis, the intensity design of the thin-skinned internal pressure cylinder is analyzed in this article.

运用应力分析理论进行了内压薄壁圆筒的强度设计。

Testing pressure factor based on Reliability Analysis on internal pressure thin wall cylinder

基于可靠度分析的外压薄壁圆筒试验压力系数

Dry air tightness test methods mainly include direct pressuredrop method and internal pressure differential method.

干式气密性检测方法主要有直接压降法和内压压差法。

Besides, thickness distribution and useful height mainly depend on axial feed but not internal pressure.

除此以外，零件的厚度分布和有效成形高度对溢流压力不敏感，其成形质量主要取决于管端的轴向进给程度。

The Elasto-Plastic Finite Element Analysis of Thick-Walled Cylinder Under Internal Pressure and Its Application to the Final Sizing Technology of Welded Pipe End

受内压厚壁圆筒的弹塑性有限元分析及其在焊管管端定径工艺中的应用

Thermal Pressure Coefficient and Internal Pressure for Binary Solutions

溶液的热压力系数及内压